

                             FP35 RS232 Command List 
                                                               2010/09/14


        The FP35 contains a number of commands which may be used with the 
        RS232 option. The exact commands which are allowed depend on the 
        specific options available in the FP35 being used.

                             Modes and Command Usage

        The FP35 limits the commands available in the various options. 
        Additionally, it will not respond to a command to place it in an 
        option or state if that option or state is not available on the 
        instrument. The following command list shows the options and 
        modes of the FP35 and the RS232 commands that are available 
        within those modes.

        In the Opening Screen of the FP35 (the state you are in when you 
        first turn the instrument on), some of the commands may not be 
        operable if the indicated option is not installed on the 
        instrument. The affected commands are indicated by the (option) 
        designation after the command in the command list below. If the 
        (option) is present after the command it indicates that the 
        option must be installed for the command to be operable. 

        In addition to the Opening Screen commands, there are State 
        commands which are in effect when a specific state is entered. 
        The available commands are limited to the indicated command set 
        when in that state or mode of operation. 

        Refer to the RS232 command reference guide for a description of 
        the individual commands and their use with the various options 
        and modes.

        Commands marked with * are dynamic data get commands. The data 
        returned by these commands may not be valid the first time you 
        read the data after changing the operating state of the FP35. You 
        may have to wait for things to settle down before reading dynamic 
        data after a change in the system.

        Commands marked with ** are get curve commands. In composite 
        mode, real time curves are dynamic, and the data may not be valid 
        after changing the state of the instrument. 

        For more information on reading dynamic data and other 
        information on programming the FP35, see the FP35NOTE.TXT file.










                                        1


        The Common commands are available in all modes in the FP35 where
        RS232 is supported.

        Command                 -- Common --                       Number 
        ----------------------------------------------------------------- 
        Set Label Information ......................................... 6
        Set Battery Test ............................................. 14
        Set Power State .............................................. 56
        Set Keyboard Lock ............................................ 62 
        Set Extended Label ........................................... 66 
        Set Keyboard Scan Code ....................................... 72
        Set Poll Delay Time .......................................... 73
        Set Battery Type ............................................. 79
        Set Average Frequencies ...................................... 82
        Set Printer Label Storage .................................... 89
        Set Printer Selection......................................... 92
        Set Printer Label Bitmap ..................................... 96
        Set Real Time Clock ......................................... 104
        Set Rcv Timeout ............................................. 132
        Set Aux Port ................................................ 148
        Set User ID Text ............................................ 166
        Set Display Mode Information ................................ 170
        Do Reset ..................................................... 38
        Get Battery Data ............................................. 19
        Get Software Version ......................................... 28
        Get Command Status ........................................... 33
        Get Keyboard Scan Code ....................................... 58
        Get Instrument State ......................................... 60
        Get Keyboard Lock ............................................ 63
        Get Poll Delay Time .......................................... 74
        Get Power State .............................................. 80  
        Get Average Frequencies ...................................... 81
        Get Extended Label ........................................... 86 
        Get Printer Selection......................................... 93
        Get Software Information ..................................... 95
        Get Device ID Count ......................................... 100
        Get Long Device ID .......................................... 101
        Get Device Data ............................................. 102
        Get Real Time Clock ......................................... 103
        Get Signal Information ...................................... 109
        Get Microphone Calibration .................................. 111
        Get Bitmap .................................................. 120
        Get Rcv Timeout ............................................. 133
        Get Aux Port ................................................ 149
        Get User Number ............................................. 151
        Get Display Mode Information ................................ 171
        Get Battery Information ..................................... 179
        Set Baudrate ............................................. 0x7c03








                                        2


        Notes: Commands 28 and 33 are always supported on all instruments 
        that follow the FIPP protocol. Generally, command 38 is supported 
        on all instruments that support the FIPP protocol, but the 
        effects of the command may be different.
        Commands 56,80,89,96,100 and above 100 are not available in all 
        instruments. Command 6 is not avail as a common cmd on the 6500.

        Be sure to check the other instrument command files to determine 
        which commands are common, and the instrument note file to 
        determine any differences between instruments for a command, as 
        well as any version related issues that might be important if you 
        intend to write a program that supports multiple instruments.

        The following tables show the commands that are available in 
        specific modes of operation on the FP35.

        Notes: 
        *  These are dynamic measurements.
        ** Curves may be dynamic in composite mode. 
        !! Entering a mode via a separate command Like Set Probe Mode is 
           an obsolete form. The method is still being supported in the 
           FP35 for backward compatibility, but the newer Set Instrument 
           State method should be used for new programs. 
        #  This command may not be supported on all instruments.
        (aud) This command only available with the audiometric option.































                                        3


        Command               -- Opening Screen (0) --             Number
        -----------------------------------------------------------------
        Set Probe Mode .................................. (Probe) ..!!. 7
        Set Instrument State ......................................... 59
        Set Option Parameters ........................................ 70
        Set User Number ............................................. 150
        Set User Mode ............................................... 192
        Do Start/Stop (press start) .................................. 16
        Do Feed ...................................................... 64
        Do Print ..................................................... 65
        Do User Message .............................................. 67
        Get Probe Mode ................................. (Probe) ..!!. 35
        Get Option Parameters ........................................ 71
        Get User Mode ............................................... 193

        Command      -- Default Setup Menu (16:0/1/2) --           Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Set User Number ............................................. 150
        Set User Mode ............................................... 192
        Do Feed ...................................................... 64
        Do Print ..................................................... 65
        Do Parameters ............................................... 177
        Get User Mode ............................................... 193

        Command        -- Print Label Screen (16:100) --           Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Set User Number ............................................. 150
        Set User Mode ............................................... 192
        Do Feed ...................................................... 64
        Do Print ..................................................... 65
        Do User Message .............................................. 67
        Get User Mode ............................................... 193

        Command    -- Top (main) Calibration Screen (*32:0) --     Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65
        Do Calibration Adjust ....................................... 144
        Do User Message .............................................. 67

        Command         -- Time Setup Screen (*32:1) --            Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65
        Do User Message .............................................. 67







                                        4


        Command      -- Mic Calibration Screen (*32:2) --          Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Set Speaker Selection ....................................... 106
        Do Feed ...................................................... 64
        Do Print ..................................................... 65
        Do User Message .............................................. 67
        Get Speaker Selection ....................................... 105
        Set Input Port .............................................. 186

        Command    -- Coupler Mic Calibration Screen (*32:3) --    Number
        -----------------------------------------------------------------
        Set Source Amplitude Value .................................... 0
        Set Harmonic Distortion Status ................................ 1
        Set Frequency Value ........................................... 2
        Set Noise Reduction Value ..................................... 4
        Set Instrument State ......................................... 59
        Set Speaker Selection ....................................... 106
        Set Impulse Rejection Value ................................. 108
        Set Analysis Selection ...................................... 174

        Do Feed ...................................................... 64
        Do Print ..................................................... 65
        Do User Message .............................................. 67
        Do Measurement ............................................... 85
        Do Calibration Adjust ....................................... 144

        Get Source Amplitude Value ................................... 21
        Get Harmonic Distortion Status ............................... 22
        Get Frequency Value .......................................... 23
        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Measurement Data .......................................*. 31
        Get Harmonic Distortion Data ...............................*. 32
        Get Gain Status .............................................. 36
        Get Speaker Selection ....................................... 105
        Get Impulse Rejection Value ................................. 107
        Get Analysis Selection ...................................... 175

        Command     -- Earphone Calibration Screen (*32:4) --      Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65
        Do User Message .............................................. 67

        *Note: Prior to V3.20 software, the Calibration screen (includes 
        Time Setup) was declared at 16:2, but this created conflicts with 
        multiple Setup menus and the Calibration sections all shared 
        minor state 2. To correct this, a new Calibration Major state was 
        declared and all calibration screens moved to that state.





                                        5


        Command       -- Help Message Window (21:0) --             Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65

        Command      -- Status Message Window (21:1) --            Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65

        Command      -- Error Message Window (21:2) --             Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65

        Command      -- Local Menu #1 Window (22:0) --             Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65

        Command      -- Local Menu #2 Window (22:1) --             Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65

        Command      -- Local Menu #3 Window (22:2) --             Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65

        Command      -- Local Menu #4 Window (22:3) --             Number
        -----------------------------------------------------------------
        Set Instrument State ......................................... 59
        Do Feed ...................................................... 64
        Do Print ..................................................... 65















                                        6


        Command -- Coupler/Target/EarSim States (1:0/26:0/27:0) -- Number 
        ----------------------------------------------------------------- 
        Set Source Amplitude Value .................................... 0
        Set Harmonic Distortion Status ................................ 1
        Set Frequency Value ........................................... 2
        Set OES Status ................................................ 3
        Set Noise Reduction Value ..................................... 4
        Set Smoothing Status .......................................... 5
        Set Probe Mode .................................. (Probe) ..!!. 7
        Set Weighting Status .......................................... 8
        Set Curve Frame Data .......................................... 9
        Set Source Method ............................................ 11
        Set Gain Status .............................................. 12
        Set Output Limiting Value .................................... 50 
        Set Reference Microphone Status ..................(Probe)..... 52 
        Set Active Status ............................................ 54 
        Set Instrument State ......................................... 59
        Set Source Magnitudes ........................................ 68
        Set Option Parameters ........................................ 70
        Set Ear Status ............................................... 75
        Set Operating Mode ........................................... 77
        Set Measurement Delay Times .................................. 84
        Set CIC Status ............................................... 87
        Set Speaker Selection ....................................... 106
        Set Impulse Rejection Value ................................. 108
        Set Selected Curve .......................................... 112
        Set Curve Status ............................................ 114
        Set Unaided Curve Selection ................................. 116
        Set User List ............................................... 118
        Set Static Tone ............................................. 121
        Set Aid Type ................................................ 123
        Set Bias Tone ............................................... 125
        Set Warble Selection ........................................ 129
        Set Fit Rule Selection ...........................(aud)...... 134
        Set Filter Selection ........................................ 136
        Set Compression Value ............................(aud)...... 138
        Set Client Age ...................................(aud)...... 140
        Set Speaker Loc ..................................(probe).... 142
        Set Leveling Data ........................................... 146
        Set Leveling State .......................................... 147
        Set Fit Type ................................................ 152
        Set Vent Type ............................................... 154
        Set Tubing Type ............................................. 156
        Set Aid Channels ............................................ 158
        Set Aid Limiting ............................................ 160
        Set Reference Method ........................................ 162
        Set Fit Parameters .......................................... 164
        Set Measurement Skew ........................................ 168
        Set Coupler Selection ....................................... 172
        Set Analysis Selection ...................................... 174
        Set Input Port .............................................. 186
        Set Difference Frequency .................................... 190




                                        7


        Command -- Coupler/Target/EarSim States (1:0/26:0/27:0) -- Number 
        -----------------------------------------------------------------
        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Feed (press feed) ......................................... 64
        Do Print (press print) ....................................... 65
        Do User Message .............................................. 67
        Do Measurement ............................................... 85
        Do User Sweep  .............................................. 176















































                                        8


        Command -- Coupler/Target/EarSim States (1:0/26:0/27:0) -- Number 
        -----------------------------------------------------------------
        Get Source Amplitude Value ................................... 21
        Get Harmonic Distortion Status ............................... 22
        Get Frequency Value .......................................... 23
        Get OES Status ............................................... 24
        Get Curve Frame Data ......................................**. 25
        Get Noise Reduction Value .................................... 26
        Get Smoothing Status ......................................... 27
        Get Leveling Status .......................................... 29
        Get Weighting Status ......................................... 30
        Get Measurement Data .......................................*. 31
        Get Harmonic Distortion Data ...............................*. 32
        Get Probe Mode .................................. (Probe) .!!. 35
        Get Gain Status .............................................. 36
        Get Source Method ............................................ 37
        Get Last Measured Curve Data ..............................**. 42
        Get Output Limit Value ....................................... 51 
        Get Reference Microphone Status ..................(Probe)..... 53 
        Get Active Status ............................................ 55
        Get Reference Microphone Input ...................(Probe)..... 57
        Get Option Parameters ........................................ 71
        Get Ear Status ............................................... 76 
        Get Operating Mode ........................................... 78
        Get Measurement Delay Times .................................. 83
        Get CIC Status ............................................... 88
        Get Speaker Selection ....................................... 105
        Get Impulse Rejection Value ................................. 107
        Get Raw Sample Data ......................................... 110
        Get Selected Curve .......................................... 113
        Get Curve Status ............................................ 115
        Get Unaided Curve Selection ................................. 117
        Get User List ............................................... 119
        Get Static Tone ............................................. 122
        Get Aid Type ................................................ 124
        Get Bias Tone ............................................... 126
        Get Warble Selection ........................................ 130
        Get Fit Rule Selection ...........................(aud)...... 135
        Get Filter Selection ........................................ 137
        Get Compression Value ............................(aud)...... 139
        Get Client Age ...................................(aud)...... 141
        Get Speaker Loc ..................................(probe).... 143
        Get Leveling Data ........................................... 145
        Get Fit Type ................................................ 153
        Get Vent Type ............................................... 155
        Get Tubing Type ............................................. 157
        Get Aid Channels ............................................ 159
        Get Aid Limiting ............................................ 161
        Get Reference Method ........................................ 163
        Get Fit Parameters .......................................... 165
        Get Measurement Skew ........................................ 169
        Get Coupler Selection ....................................... 173
        Get Analysis Selection ...................................... 175
        Get Input Port .............................................. 187
        Get Difference Frequency .................................... 191

                                        9


























































                                       10


        Command          -- Real Ear (Probe) State (6) --          Number
        -----------------------------------------------------------------
        Set Source Amplitude Value .................................... 0
        Set Harmonic Distortion Status ................................ 1
        Set Frequency Value ........................................... 2
        Set Noise Reduction Value ..................................... 4
        Set Smoothing Status .......................................... 5
        Set Probe Mode .................................. (Probe) ..!!. 7
        Set Curve Frame Data .......................................... 9
        Set Source Method ............................................ 11
        Set Automatic Mode ........................................... 48
        Set Output Limiting Value .................................... 50 
        Set Reference Microphone Status .............................. 52 
        Set Active Status ............................................ 54 
        Set Instrument State ......................................... 59
        Set Source Magnitudes ........................................ 68
        Set Option Parameters ........................................ 70
        Set Ear Status ............................................... 75
        Set Operating Mode ........................................... 77
        Set Measurement Delay Times .................................. 84
        Set Speaker Selection ....................................... 106
        Set Impulse Rejection Value ................................. 108
        Set Selected Curve .......................................... 112
        Set Curve Status ............................................ 114
        Set Unaided Curve Selection ................................. 116
        Set Static Tone ............................................. 121
        Set Aid Type ................................................ 123
        Set Bias Tone ............................................... 125
        Set Warble Selection ........................................ 129
        Set Filter Selection ........................................ 136
        Set Fit Rule Selection ...........................(aud)...... 134
        Set Compression Value ............................(aud)...... 138
        Set Client Age ...................................(aud)...... 140
        Set Speaker Loc ..................................(probe).... 142
        Set Leveling Data ........................................... 146
        Set Leveling State .......................................... 147
        Set Fit Type ................................................ 152
        Set Vent Type ............................................... 154
        Set Tubing Type ............................................. 156
        Set Aid Channels ............................................ 158
        Set Aid Limiting ............................................ 160
        Set Reference Method ........................................ 162
        Set Fit Parameters .......................................... 164
        Set Measurement Skew ........................................ 168
        Set Analysis Selection ...................................... 174
        Set Input Port .............................................. 186
        Set Difference Frequency .................................... 190

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Feed (press feed) ......................................... 64
        Do Print (press print) ....................................... 65
        Do User Message .............................................. 67
        Do User Sweep  .............................................. 176


                                       11


        Command           -- Real Ear (Probe) State (6) --         Number
        -----------------------------------------------------------------
        Get Source Amplitude Value ................................... 21
        Get Harmonic Distortion Status ............................... 22
        Get Frequency Value .......................................... 23
        Get Curve Frame Data ......................................**. 25
        Get Noise Reduction Value .................................... 26
        Get Smoothing Status ......................................... 27
        Get Leveling Status .......................................... 29
        Get Weighting Status ......................................... 30
        Get Measurement Data ...................... (single tone) ..*. 31
        Get Harmonic Distortion Data ...............................*. 32
        Get Probe Mode ................................. (Probe) ..!!. 35
        Get Gain Status .............................................. 36
        Get Source Method ............................................ 37
        Get Last Measured Curve Data ..............................**. 42
        Get Automatic Status ......................................... 49
        Get Output Limit Value ....................................... 51 
        Get Reference Microphone Status .............................. 53 
        Get Active Status ............................................ 55 
        Get Reference Microphone Input ............................... 57
        Get Option Parameters ........................................ 71
        Get Ear Status ............................................... 76 
        Get Operating Mode ........................................... 78
        Get Measurement Delay Times .................................. 83
        Get Speaker Selection ....................................... 105
        Get Impulse Rejection Value ................................. 107
        Get Raw Sample Data ......................................... 110
        Get Selected Curve .......................................... 113
        Get Curve Status ............................................ 115
        Get Unaided Curve Selection ................................. 117
        Get User List ............................................... 119
        Get Static Tone ............................................. 122
        Get Aid Type ................................................ 124
        Get Bias Tone ............................................... 126
        Get Warble Selection ........................................ 130
        Get Fit Rule Selection ...........................(aud)...... 135
        Get Filter Selection ........................................ 137
        Get Compression Value ............................(aud)...... 139
        Get Client Age ...................................(aud)...... 141
        Get Speaker Loc ..................................(probe).... 143
        Get Leveling Data ........................................... 145
        Get Fit Type ................................................ 153
        Get Vent Type ............................................... 155
        Get Tubing Type ............................................. 157
        Get Aid Channels ............................................ 159
        Get Aid Limiting ............................................ 161
        Get Reference Method ........................................ 163
        Get Fit Parameters .......................................... 165
        Get Measurement Skew ........................................ 169
        Get Analysis Selection ...................................... 175
        Get Input Port .............................................. 187
        Get Difference Frequency .................................... 191



                                       12


        Command                -- Audiogram Screen (25:0) --       Number
        -----------------------------------------------------------------
        Set Amplitude Value ..............................(aud)........ 0
        Set Frequency Value ..............................(aud)........ 2
        Set Noise Reduction Value ..................................... 4
        Set Probe Mode .................................. (Probe) ..!!. 7
        Set Curve Frame Data .......................................... 9
        Set Output Limiting Value .................................... 50 
        Set Reference Microphone Status ..................(aud)....... 52 
        Set Active Status ............................................ 54 
        Set Instrument State ......................................... 59
        Set Option Parameters ........................................ 70
        Set Ear Status ............................................... 75
        Set Speaker Selection ....................................... 106
        Set Impulse Rejection Value ................................. 108
        Set Selected Curve .......................................... 112
        Set Curve Status ............................................ 114
        Set Aid Information ......................................... 123
        Set Warble Selection .............................(aud)...... 129
        Set Fit Rule Selection ...........................(aud)...... 134
        Set Compression Value ............................(aud)...... 138
        Set Client Age ...................................(aud)...... 140
        Set Speaker Loc ..................................(probe).... 142
        Set Leveling Data ........................................... 146
        Set Leveling State .......................................... 147
        Set Fit Type ................................................ 152
        Set Vent Type ............................................... 154
        Set Tubing Type ............................................. 156
        Set Aid Channels ............................................ 158
        Set Aid Limiting ............................................ 160
        Set Fit Parameters .......................................... 164
        Set Analysis Selection ...................................... 174
        Set Input Port .............................................. 186























                                       13


        Command                -- Audiogram Screen (25:0) --       Number
        -----------------------------------------------------------------
        Get Amplitude Value ..............................(aud)....... 21
        Get Frequency Value ..............................(aud)....... 23
        Get Curve Frame Data ......................................**. 25
        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Measurement Data .............................(aud).....*. 31
        Get Probe Mode ................................. (Probe) ..!!. 35
        Get Output Limit Value ....................................... 51 
        Get Reference Microphone Status ..................(aud)....... 53 
        Get Active Status ............................................ 55 
        Get Reference Microphone Input ...................(aud)....... 57
        Get Option Parameters ........................................ 71
        Get Ear Status ............................................... 76 
        Get Speaker Selection ....................................... 105
        Get Impulse Rejection Value ................................. 107
        Get Raw Sample Data ......................................... 110
        Get Selected Curve .......................................... 113
        Get Curve Status ............................................ 115
        Get Aid Information ......................................... 124
        Get Warble Selection .............................(aud)...... 130
        Get Fit Rule Selection ...........................(aud)...... 135
        Get Compression Value ............................(aud)...... 139
        Get Client Age ...................................(aud)...... 141
        Get Speaker Loc ..................................(probe).... 143
        Get Leveling Data ........................................... 145
        Get Fit Type ................................................ 153
        Get Vent Type ............................................... 155
        Get Tubing Type ............................................. 157
        Get Aid Channels ............................................ 159
        Get Aid Limiting ............................................ 161
        Get Fit Parameters .......................................... 165
        Get Analysis Selection ...................................... 175
        Get Input Port .............................................. 187

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Feed (press feed) ......................................... 64
        Do Print (press print) ....................................... 65
        Do User Message .............................................. 67
        Do Target ................................................... 178














                                       14


        Command            -- IEC 94/05 option (3/37) --           Number
        -----------------------------------------------------------------
                   IEC 94/05 Minor State #0 (IEC mode entry)
        Set Noise Reduction Value ..................................... 4
        Set Reference Microphone Status .............................. 52 
        Set Active Status ............................................ 54
        Set Instrument State ......................................... 59
        Set Operating Parameters ..................................... 70
        Set Measurement Delay Times .................................. 84
        Set Blob ...................................................#. 99
        Set Aid Type ................................................ 123
        Set Input Port .............................................. 186

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Reference Microphone Status ..................(Probe)..... 53 
        Get Active Status ............................................ 55 
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124
        Get Input Port .............................................. 187

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Feed (press feed) ......................................... 64
        Do Print (press print) ....................................... 65
        Do User Message .............................................. 67

               IEC 94 Minor State #1 (Set reference test gain)
               IEC 05 Minor States #1, #2, #3, #4 
        Set Active Status ............................................ 54
        Set Instrument State ......................................... 59
        Set Measurement Delay Times .................................. 84

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Measurement Data .......................................*. 31
        Get Reference Microphone Status ..................(Probe)..... 53
        Get Active Status ............................................ 55 
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124

        Do Start/Stop (press start) .................................. 16
        Do Feed ...................................................... 64
        Do Print ..................................................... 65









                                       15


        Command          -- IEC 94/05 option (3/37) --             Number
        -----------------------------------------------------------------
                    IEC 94 Minor State #2 (Test complete)
                    IEC 05 Minor State #5 (Test complete)
        Set Noise Reduction Value ..................................... 4
        Set Reference Microphone Status .............................. 52 
        Set Active Mode .............................................. 54
        Set Instrument State ......................................... 59
        Set Operating Parameters ..................................... 70
        Set Measurement Delay Times .................................. 84
        Set Blob ...................................................#. 99
        Set Aid Type ................................................ 123
        Set Input Port .............................................. 186

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Last Measured Curve Data ..............................**. 42
        Get Reference Microphone Status .............................. 53 
        Get Active Status ............................................ 55 
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124
        Get Input Port .............................................. 187

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17





























                                       16


        Command    -- ANSI96/ANSI03/ACIC Mode (18/15) --  Notes    Number 
        -----------------------------------------------------------------
                  Minor State #0 (ANSI96/ANSI03/ACIC Entry)
        Set Noise Reduction Value ..................................... 4
        Set Reference Microphone Status .................(Probe)...... 52
        Set Active Status ............................................ 54 
        Set Instrument State ......................................... 59
        Set Operating Parameters ..................................... 70
        Set Measurement Delay Times .................................. 84
        Set Blob ...................................................#. 99
        Set Aid Type ................................................ 123
        Set Input Port .............................................. 186

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Last Measured Curve Data ..............................**. 42
        Get Reference Microphone Status .................(Probe)...... 53 
        Get Active Status ............................................ 55
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124
        Get Input Port .............................................. 187

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Line Feed ................................................. 64
        Do Print ..................................................... 65
        Do User Message .............................................. 67


                       Minor State #1 (Set reference test gain)
        Set Active Status ............................................ 54 
        Set Instrument State ......................................... 59
        Set Measurement Delay Times .................................. 84

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Measurement Data .......................................*. 31
        Get Reference Microphone Status .................(Probe)...... 53 
        Get Active Status ............................................ 55
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124

        Do Start/Stop (press start) .................................. 16










                                       17


        Command --- ANSI96/ANSI03/*ACIC Mode (18/33/*15) --- Notes Number 
        -----------------------------------------------------------------
                   Minor State #2 (Set max telecoil output)
        Set Active Status ............................................ 54 
        Set Instrument State ......................................... 59
        Set Measurement Delay Times .................................. 84

        Get Noise Reduction Value .................................... 26
        Get Measurement Data .......................................*. 31
        Get Leveling Status .......................................... 29
        Get Measurement Data .......................................*. 31
        Get Reference Microphone Status .................(Probe)...... 53 
        Get Active Status ............................................ 55
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124

        Do Start/Stop (press start) .................................. 16


                Minor State #3 (Exit telecoil and/or set AGC)
        Set Active Status ............................................ 54 
        Set Instrument State ......................................... 59
        Set Measurement Delay Times .................................. 84

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Reference Microphone Status .................(Probe)...... 53 
        Get Active Status ............................................ 55
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124

        Do Start/Stop (press start) .................................. 16




















                                       18


        Command --- ANSI96/ANSI03/*ACIC Mode (18/33/*15) --- Notes Number 
        -----------------------------------------------------------------
                         Minor State #4 (Test complete).
        Set Noise Reduction Value ..................................... 4
        Set Reference Microphone Status .................(Probe)...... 52
        Set Active Status ............................................ 54 
        Set Instrument State ......................................... 59
        Set Operating Parameters ..................................... 70
        Set Measurement Delay Times .................................. 84
        Set Blob ...................................................#. 99
        Set Aid Type ................................................ 123
        Set Input Port .............................................. 186

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Last Measured Curve Data ..............................**. 42
        Get Reference Microphone Status .................(Probe)...... 53 
        Get Active Status ............................................ 55
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124
        Get Input Port .............................................. 187

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Line Feed ................................................. 64
        Do Print ..................................................... 65
        Do User Message .............................................. 67

        *Note: The ACIC test is obsolete and not available as of V3.50.

























                                       19


        Command                -- JIS state (4) --                 Number
        -----------------------------------------------------------------
                       JIS Minor State #0 (JIS mode entry)
        Set Noise Reduction Value ..................................... 4
        Set Reference Microphone Status .............................. 52 
        Set Active Status ............................................ 54
        Set Instrument State ......................................... 59
        Set Operating Parameters ..................................... 70
        Set Measurement Delay Times .................................. 84
        Set Blob ...................................................#. 99
        Set Aid Type ................................................ 123
        Set Input Port .............................................. 186

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Reference Microphone Status .................(Probe)...... 53 
        Get Active Status ............................................ 55 
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124
        Get Input Port .............................................. 187

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Feed (press feed) ......................................... 64 
        Do Print (press print) ....................................... 65
        Do User Message .............................................. 67

                   JIS Minor State #1 (Set reference test gain)
        Set Active Status ............................................ 54
        Set Instrument State ......................................... 59
        Set Measurement Delay Times .................................. 84

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Measurement Data .......................................*. 31
        Get Reference Microphone Status .................(Probe)...... 53 
        Get Active Status ............................................ 55 
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124

        Do Start/Stop (press start) .................................. 16
        Do Feed (press feed) ......................................... 64 
        Do Print (press print) ....................................... 65










                                       20


        Command                -- JIS state (4) --                 Number
        -----------------------------------------------------------------
                       JIS Minor State #2 (Test complete)
        Set Noise Reduction Value ..................................... 4
        Set Reference Microphone Status .............................. 52 
        Set Active Mode .............................................. 54
        Set Instrument State ......................................... 59
        Set Operating Parameters ..................................... 70
        Set Measurement Delay Times .................................. 84
        Set Blob ...................................................#. 99
        Set Aid Type ................................................ 123
        Set Input Port .............................................. 186

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Last Measured Curve Data ................................. 42
        Get Reference Microphone Status .................(Probe)...... 53 
        Get Active Status ............................................ 55 
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124
        Get Input Port .............................................. 187

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Feed (press feed) ......................................... 64 
        Do Print (press print) ....................................... 65
        Do User Message .............................................. 67



























                                       21


        Command                -- ISI option (5) --                Number
        -----------------------------------------------------------------
                        ISI Minor State #0 (ISI mode entry)
        Set Noise Reduction Value ..................................... 4
        Set Reference Microphone Status .............................. 52 
        Set Active Status ............................................ 54
        Set Instrument State ......................................... 59
        Set Operating Parameters ..................................... 70
        Set Measurement Delay Times .................................. 84
        Set Blob ...................................................#. 99
        Set Aid Type ................................................ 123
        Set Input Port .............................................. 186

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Last Measured Curve Data ..............................**. 42
        Get Reference Microphone Status ..................(Probe)..... 53 
        Get Active Status ............................................ 55 
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124
        Get Input Port .............................................. 187

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Feed (press feed) ......................................... 64
        Do Print (press print) ....................................... 65
        Do User Message .............................................. 67

                  ISI Minor State #1 (Set reference test gain)
        Set Active Status ............................................ 54
        Set Instrument State ......................................... 59
        Set Measurement Delay Times .................................. 84

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Measurement Data .......................................*. 31
        Get Reference Microphone Status ..................(Probe)..... 53
        Get Active Status ............................................ 55 
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124

        Do Start/Stop (press start) .................................. 16
        Do Feed ...................................................... 64
        Do Print ..................................................... 65









                                       22


        Command                -- ISI option (5) --                Number
        -----------------------------------------------------------------
                       ISI Minor State #2 (Test complete)
        Set Noise Reduction Value ..................................... 4
        Set Reference Microphone Status .............................. 52 
        Set Active Mode .............................................. 54
        Set Instrument State ......................................... 59
        Set Operating Parameters ..................................... 70
        Set Measurement Delay Times .................................. 84
        Set Blob ...................................................#. 99
        Set Aid Type ................................................ 123
        Set Input Port .............................................. 186

        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Last Measured Curve Data ..............................**. 42
        Get Reference Microphone Status .............................. 53 
        Get Active Status ............................................ 55 
        Get Blob ..................................................... 61
        Get Operating Parameters ..................................... 71
        Get Measurement Delay Times .................................. 83
        Get Aid Type ................................................ 124
        Get Input Port .............................................. 187

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Feed ...................................................... 64
        Do Print ..................................................... 65
        Do User Message .............................................. 67



























                                       23


        Command              -- O'Scope option (34:0) --           Number
        -----------------------------------------------------------------
        Set Source Amplitude Value .................................... 0
        Set Harmonic Distortion Status ................................ 1
        Set Frequency Value ........................................... 2
        Set Noise Reduction Value ..................................... 4
        Set Source Method ............................................ 11
        Set Output Limit Value ....................................... 50 
        Set Reference Microphone Status ..................(Probe)..... 52 
        Set Active Status ............................................ 54 
        Set Instrument State ......................................... 59
        Set Source Magnitudes ........................................ 68
        Set Operating Mode ........................................... 77
        Set Speaker Selection ....................................... 106
        Set Impulse Rejection Value ................................. 108
        Set Selected Curve .......................................... 112
        Set Curve Status ............................................ 114
        Set Warble Selection ........................................ 129
        Set Filter Selection ........................................ 136
        Set Leveling Data ........................................... 146
        Set Leveling State .......................................... 147
        Set Analysis Selection ...................................... 174
        Set Input Port .............................................. 186
        Set Difference Frequency .................................... 190

        Do Start/Stop (press start) .................................. 16
        Do Leveling (press level) .................................... 17
        Do Feed (press feed) ......................................... 64
        Do Print (press print) ....................................... 65
        Do User Message .............................................. 67

        Get Source Amplitude Value ................................... 21
        Get Harmonic Distortion Status ............................... 22
        Get Frequency Value .......................................... 23
        Get Noise Reduction Value .................................... 26
        Get Leveling Status .......................................... 29
        Get Measurement Data .......................................*. 31
        Get Harmonic Distortion Data ...............................*. 32
        Get Source Method ............................................ 37
        Get Output Limit Value ....................................... 51 
        Get Reference Microphone Status ..................(Probe)..... 53 
        Get Active Status ............................................ 55
        Get Reference Microphone Input ...................(Probe)..... 57
        Get Operating Mode ........................................... 78
        Get Speaker Selection ....................................... 105
        Get Impulse Rejection Value ................................. 107
        Get Raw Sample Data ......................................... 110
        Get Selected Curve .......................................... 113
        Get Curve Status ............................................ 115
        Get Warble Selection ........................................ 130
        Get Filter Selection ........................................ 137
        Get Leveling Data ........................................... 145
        Get Analysis Selection ...................................... 175
        Get Input Port .............................................. 187
        Get Difference Frequency .................................... 191

                                       24



        <end> -med






















































                                       25
